You should be able to flush it either way. Just getting the block cleaned out is what needs to be done. My guess is that people suggest flushing with the old water pump on just because it will save you time, since you are going to drain the entire system when you install the new pump.
Do you need to flush coolant when replacing water pump?
Ensure that the properly rinsed coolant is flushed out in the event of a bad repair. For water pumps that will never be flushed before installation, you need to first flush the cooling system first. You can perform this lab on a vehicle in a shop or a vehicle for your client who needs to keep their Thermostat running.
Does radiator flush damage water pump?
In order to prevent the old anti-freeze from becoming acidic, it is important to flush it. Once it starts to become acidic, it will break down and damage the bearing in the water pump, rubber hoses, and aluminum parts of the engine.
When should you flush your cooling system?
If you find that your temperature gauge is always high and your engine is frequently overheating, chances are that you need a coolant flush. Allowing your engine to overheat can cause serious, costly problems, so it is best to visit a mechanic at the first signs of temperature issues.
When replacing a water pump What else should you replace?
So when the water pump must be replaced, it is a good idea to go ahead and also replace the timing belt, timing belt tensioner and idler pulleys.
Can I just replace the water pump gasket?
When changing a water pump, replace all old gaskets and seals with new ones. If your new pump comes with a seal, make sure it’s in impeccable condition before installing it. (Some seals are so thin you could easily damage them when you rip off the packaging.)
What all do you need to change a water pump?
TO CHANGE YOUR WATER PUMP YOU WILL NEED:
- Sockets and wrenches.
- Screwdriver.
- Pliers.
- Drain pan.
- Rags.
- Gasket sealer.
- Antifreeze.
Can a coolant flush damage your engine?
Getting a coolant flush will prevent the old anti-freeze from becoming acidic. This is important because once it starts to become acidic it will break down and can damage the bearing in the water pump, the rubber hoses and the aluminum components of the engine.
Can a coolant flush cause problems?
No, a radiator flush won’t cause problems if it is done correctly and flushes everything out as it is intended, then your car will run the same or better.
Is a coolant flush the same as a radiator flush?
A coolant flush is another name for radiator flush, a procedure to clean your vehicle’s cooling system of sediment and rust. The coolant keeps your engine from overheating while running, and from freezing in cold weather when it’s not running.
How often water pump should be replaced?
Typically, the recommended interval for replacing the water pump is every 60,000 to 100,000 miles, depending on various factors, such as the car model, road and weather conditions, and driving behavior. Therefore, if you plan to invest in a used car, ensure you verify whether the seller replaced the water pump.
How long does it take to put a water pump on?
Fixing a broken water pump can take anywhere from two hours to most of a day. A simple replacement should take around two hours, but more complicated work trying to fix a water pump (which will save you money on parts) can take four or more hours.
Do you need to use gasket sealer on a water pump?
You don’t need sealer on the pump gasket if you already put the sealer onto the pump. The gasket is good enough on the engine, you don’t need to put sealer on that. It’s a good idea to put it on the pump. Then it stays in place and doesn’t move.
Do I need to use RTV on my water pump gasket?
If a reputable manufacturer asks you to install a water pump gasket on a clean and dry surface, adding RTV may affect compression or permanently damage the gasket, leading to leaks. It’s safe to use RTV only if recommended in the service manual.
What is best sealant for water pump gasket?
Permatex Water Pump and Thermostat RTV Silicone Gasket is a non-corrosive, sensor-safe RTV silicone gasket material formulated specifically for water pumps and thermostat housings. This gasket maker has the highest water-glycol resistance available in an RTV silicone.
Can I use gasket maker on water pump?
Permatex Water Pump & Thermostat RTV Silicone Gasket Maker is a noncorrosive, sensor-safe RTV silicone gasket material formulated for water pumps and thermostat housings.
Can I use black RTV on water pump?
IMO it should be fine with just the o-ring, or even with a dab of rtv to just hold it in place.
How long does it take for water pump gasket to dry?
Typically, RTVs require a minimum of two hours to set up and 24-hours to achieve the full cure that’s needed before adding fluids or returning the vehicle to service.