VW Jetta parking brake loose after rear brakes replaced. Is it related?


Why does my parking brake feel loose?

If you’re e-brake feels loose, it’s usually the wires that simply need to be re-adjusted. Most mechanical e-brakes are activated using thin steel cables that run from your e-brake handle, down to your brake mechanism. Over time, these cables develop slack and need to be re-adjusted.

Does the parking brake use the rear brakes?

A parking brake controls the rear brakes and is a completely separate device from your vehicle’s regular hydraulic brakes. It is in charge of keeping a parked vehicle stationary; it will prevent the car from rolling down a hill or moving.

How do you adjust the emergency brake on a Volkswagen Jetta?

antennamediatorino.eu
This is what we're working with here. So that's nut right there is the adjustment. So obviously you tighten it to make it tighter and loosen it so i'm going to loosen it a little bit and feel it out.

Is it safe to drive with loose handbrake?

The faster and the further you travel with the handbrake engaged, the more damage you can do to your car. But even at short distances and low speeds, driving with your parking brake engaged can cause a glaze to build up on your brake pads.

How much does it cost to adjust the parking brake?

between $56 and $70

The average cost for parking brake system adjust is between $56 and $70. Labor costs are estimated between $56 and $70. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.

How do I know if my parking brake cable is stretched?

Sometimes, a stretched, loose, misaligned or snagged cable affects the feel of your handbrake. For example, it might feel stiffer than usual when you move the handle up or down. Or, the handle might feel loose and wobbly. You might need to put more effort into locking it into its on or off positions.

How do you know if your parking brake is bad?

There are a few symptoms to watch out for when your parking brake drum starts to go bad.

  1. Parking brake won’t hold. If you notice your parking brake will not hold, there may be a problem with the rear brake adjustment. …
  2. Poor braking. …
  3. Keep your parking brake working well.


What is the parking brake connected to?

rear brakes

The parking brake is connected to the rear brakes, which do not exert as much force in braking as the front brakes and will do little to stop a vehicle moving at high speeds. Most modern applications of the parking brake is to ensure that a parked vehicle stays in place, especially on hills and other declines.

Do parking brakes self adjust?

Parking brake shoes are designed to self-adjust, but the self-adjusting system can often fail. The brake shoe is housed in the drum and experiences lots of heat and brake dust that eventually leads to wear and tear.

How do you know if your handbrake cable has snapped?

For example, a good sign that the cable is deteriorating is when you have to pull the handbrake lever up higher than normal to stop the car. When a handbrake cable does completely snap the consequences can be catastrophic. It will mean that there is nothing to lock the car in its place when stationary.

How many clicks should a parking brake have?

A normal handbrake should take between 5 and 8 clicks – more than this and it could be too tight, causing damage to the rear brakes and less than 5 means it’s likely to be dragging and could fail completely.

How long does it take to replace a handbrake cable?

A handbrake cable replacement usually takes around 1.5 hours, but can take less or more time.

How do you tighten a parking brake cable?

Pull the handbrake lever ‘on’ until slight resistance is felt at the lever; then try turning each rear wheel. Each should turn with equal resistance. If they do not, tighten the cable on the slacker side until both feel equal. Tighten the locknuts.

How do you tighten a handbrake cable?

antennamediatorino.eu
So the handbrake actually tightens. So you're going to need a 12 millimeter deep socket socket. Long extensions and then you ratchet that's how long this needs to be in order to get access to it.